Tear-off
Old roofing is removed and the deck is repaired for a sound start.
Flat Roofing
Rubber Roof Installation Succasunna, NJ
Installing a rubber roof in Succasunna means choosing the EPDM thickness and attachment method, then flashing walls, curbs and edges so the membrane can move without tearing, so the roof handles sun, cold and storms for decades. Dial (862) 453-8001 to talk with a local roofer about a new rubber roof.
A true rubber roof is EPDM, a synthetic rubber membrane used on flat and low slope roofs for decades. It comes in large, flexible sheets, most often black, in 45 or 60 mil thickness, and its biggest strength is that it stays flexible in heat and cold without cracking. Unlike TPO and PVC, its seams are taped rather than heat welded.
EPDM can be attached in three main ways. The sheet can be glued to the substrate, fastened with plates at the seams or laid loose under a layer of stone. Residential roofs are most often fully adhered.
Thickness and color are the next choices. A 60 mil sheet is tougher than 45 mil for roofs that see foot traffic. Black is standard and holds heat, while white reflects it. Where the rubber meets a shingled roof or the house wall, the tie-in detail matters as much as any of these choices.
If the problem goes deeper than it first looked, a Succasunna roofer may also recommend rubber roof repair or flat roof installation.
Need rubber roof installation in Succasunna? Call (862) 453-8001 and describe the problem to a roofer who works in Succasunna.
Call nowThe process
How rubber roof installation works
A rubber roof is built in layers, with the seams and flashing as the critical details.
Check the base
Damaged decking is replaced and drainage is confirmed before any insulation goes down. A tear-off comes first on existing roofs.
Add the cover board
Insulation boards go down for energy savings and slope, topped by a smooth cover board. Tapered boards add slope where needed.
Lay the sheet
The EPDM is unrolled, positioned and left to relax so wrinkles flatten before any adhesive goes on. Seams are planned so they run with the slope.
Adhering
Half the sheet is folded back, adhesive is applied to both surfaces and the rubber is pressed into place. Then the other half is done the same way. Air pockets left under the sheet can turn into blisters later, so the crew works the rubber flat from the center out.
Seal the seams
Seam areas are cleaned and primed, then seam tape is applied and rolled firmly with a seam roller. Tape edges are finished with lap sealant.
Flashing
Flashing goes up walls and around curbs, with boots at pipes and new edge metal at the perimeter. Termination bar and counter flashing seal the wall edge. The last step is probing each seam and patch for gaps.
What is included
Parts of a new EPDM roof
Cover board
Rigid insulation and a cover board form the base under the rubber.
Seam tape
Every seam gets primer and tape with lap sealant at the edges.
Edge metal
Walls, curbs, pipes and edges are flashed with materials made for EPDM.
Rubber sheet
The rubber membrane is adhered or fastened over a clean, dry base.
Related service
EPDM Roof Installation Succasunna, NJ
Installing EPDM well comes down to preparation, seams and flashing. Rushing the adhesive, skipping primer or leaving wrinkles under the sheet are the common mistakes. Dry, mild days give the best bond. Some installers use water-based adhesive for the field of the roof and solvent-based adhesive at walls and curbs, where the grip has to be strongest.
For a Succasunna home, the installer thinks ahead to how the roof will behave over the years. Securing the membrane at the edges and flashing corners correctly prevents later tears. Ask how the roofer secures the perimeter.
Local help
Rubber Roof Installation Near Me
Around Succasunna, homeowners often choose EPDM for flat roof sections because it is durable and easy to repair. Across Succasunna and nearby towns like Ledgewood, Flanders, Landing and Netcong, EPDM handles storms, sun and cold well when it is installed with good seams and drainage, which is why the seams and flashing deserve careful attention.
Need rubber roof installation around Succasunna? Call (862) 453-8001 for a Succasunna roofer who serves the towns around it too.
What the local climate does to a roof
Winters here are long and cold, with snow on the roof for weeks at a time and plenty of nights below freezing. When warm attic air melts the snow, the meltwater runs down and freezes again at the eaves, which is how ice dams form and back water up under the shingles. Strong coastal storms push rain into every weak spot at the flashing and valleys. That is why roof repair in Succasunna is busiest after a hard winter and before the next one.
Why call
Why act early
Smaller repairs
A roof problem fixed early rarely spreads to the decking, the insulation or the ceilings.
Roofers who know Succasunna
Roofers in Succasunna know the roof types and weather wear common in local homes.
Know what happens next
Ask your questions before you agree to anything.
Rubber Roof Installation FAQ
Which EPDM thickness should I choose?
Most residential EPDM is 45 or 60 mil. Thicker 60 mil is tougher and longer lasting. Even thicker sheets are available for demanding roofs.
What is the difference between EPDM and TPO?
EPDM is synthetic rubber, while TPO is a thermoplastic membrane. EPDM is usually black, very flexible and seamed with tape, while TPO is usually white, more reflective and heat welded at the seams. Both are common on flat roofs.
What color EPDM is best?
Black and white each have their place. Black EPDM absorbs heat, which can help in cold climates, while white EPDM reflects sunlight and keeps the rooms below cooler. Ask about both options.
How long does a new rubber roof last?
Rubber roofs often last decades. Thickness, seam quality and maintenance all affect its life. Small repairs are easy to make.
Can a rubber roof go over an existing roof?
Recovering depends on the condition of the old roof. Codes generally allow one recover over a dry, sound roof. If the old roof is wet, it must come off. Core samples or a moisture scan show whether the old roof is dry enough.
More questions? Call (862) 453-8001
Often needed together
Rubber Roof Repair
Repairs for leaking rubber roofs, from peeling seams to pulled flashing at walls and curbs, after the real leak point is found.
Learn moreFlat Roof Installation
New flat roofs built with real slope, insulation, a cover board and a membrane suited to the building, so water drains instead of ponding.
Learn moreTPO Roofing
TPO membrane roofs installed over new insulation or in place of a worn flat roof, with seams welded into one watertight sheet.
Learn moreFlat Roof Replacement
Replacing old built-up, torch-down, EPDM or TPO roofs with a new system built to drain, so ponding and repeat leaks end for good.
Learn more
Looking for something else?
See all roofing servicesNeed rubber roof installation in Succasunna, NJ?
Call (862) 453-8001 to talk to a roofer serving Succasunna, NJ.